Elektriskais pacēlājs

Pārskats
pacēlājs ir lietots iekšā dažādi liela mēroga ūdens padeve un drenāža, ūdens taupīšana un hidroenerģija projekti. Tas tiek izmantots tiek izmantots kontrolē pacelšana un nolaišana dažādi lieli un vidēja izmēra cast dzelzs vārti un tērauds vārti to sasniegt mērķis atvēršana un aizvēršana. Darbs princips of elektriskais pacēlājs is tas pacēlājs piedziņa pacēlājs uzgrieznis uzgrieznis pagrieziens, un zem darbība of the trapecveida vītne, the skrūve stienis piedziņas the weir vārti korpuss to run up and down, so as to cut off or dredge the water flow. It ir funkcijas of light weight, flexible operation, antikorozija, no rust, convenient installation and maintenance, and reliable sealing. Engineering, used as cut-off, regulēšana plūsma and kontrole ūdens līmenis. The regulating weir gate is general installed on the upper part of the pool to adjust the water level in the pool, such as the distribution well of the aerācija tank or some water outlets.
Uzvilkt
pacēlājs ir galvenokārt sastāv of motor, palēninājums ierīce un weir durvis montāža. The motors piedziņas the skrūve stienis on augšējā daļa of the weir vārti caur palēninājums ierīce. Caur the vertikāli pārvietojums of the skrūve stienis stienis, the weir vārti ir vilkts by the eņģe mašīna to mainīt leņķis ar šķidrums virsma, so as to sasniegt mērķis mainīt mainīt ūdens līmenis un kontrole plūsma.
Līdzekļi
1. Flexible action, good sealing performance and high degree of automation.
2. Laba pielāgošanās spēja darbs vide un ilgs serviss kalpošanas laiks kalpošanas laiks.
3. Aprīkots ar takts robeža un jauda pārslodze aizsardzība, drošs un uzticams darbs.
4. It is easy to combine structures, easy to install and maintain.

role of electric pacēlājs
Elektriskais pacēlājs ir galvenokārt lietots lai kontrolētu pacēlāju of dažādi vārti, weir vārti un vārsti, so as to realize the opening and closing of gates or valves. It is general daled into manual and electric control. When the gate or weir gate has a large ratio of width to height, a double lifting point hoist is required.

Kad uzstādīšana elektriskais pacēlājs, it ir nepieciešams lai paturētu pamatu izkārtojumu plakni of the base at 180o; the contact area between the hoist base and the foundation layout plane must reach more than 90%; the skrūve ass must be perpendikulārs to the horizontal plakne mērīts on the gate platform; it must be hung ar the gate the earholes are aligned and vertical to prevent the skrūve from tilts% 2c cēlonis lokāls stress un bojājums uz mašīna.
Vieta rokasgrāmata elektriskais pacēlājs at uzstādīšana atrašanās vieta. Ielieciet a a ierobežojošs disks ieslēgts 2 c skrūve skrūve stieņa iekšā mašīna no apakšējā daļa no sijas % 2c kad skrūve stienis ir ir pakļauts no augšas no mašīnas %2 c vāks augšējais ierobežojošais disks atkal . Apakšā no skrūves stieņa ir savienots ar vārtiem.
pamats uzstādīšanai pacēlājs jābūt cietam un drošam. Betons priekš mašīna pamatne pamats sastāvdaļas jābūt jālej saskaņā ar to the rasējumi. Kad betons stiprība nav nesasniedz dizains stiprība, it is nav atļauts to demontēt un mainīt pagaidu atbalsts of the pacēlājs, let alone carry out trial adjustment and trial operation operation.
Laikā uzstādīšana, saskaņā to pacēliens centrs līnija of the gate, find the center so that the vertical and horizontal center line deviation does not exceed plus or mīnus 3mm, and the elevation novirze does not exceed plus or mīnus 5mm. Then pour the second-stage concrete or connect with the embeddeded steel plate.
uzstādīšana of the electrical equipment of the product mustly with requirements of the rasējumi and instrukcijas, and all electric equipment must be uzticami iezemēti.
Pēc the product is installed, it is need to clean the machine, repair the damaged protective paint, and inject grease.
Parametrus
Jauda padeve:
380V AC+ 10%150Hz5%, or pielāgots
220V AC+ 10% 150Hz ± 5%, or pielāgots
Ieeja signāls:
A) Analogais 4mA-20mADC, ieeja pretestība 2500
B) Pārslēgšanās aktīvs 24VDC
C) Profibus-DP vai MODBUS (pēc izvēles)
A) 4mA~20mADC, negatīva pretestība Mazāk nekā vai vienāds līdz 7500
B) 6 komplekti of pasīvie kontakti
C) PROFIBUS vai MODBUS (pēc izvēles)
Pamata kļūda ierobežojums: s1%
Atkārtojamība kļūda: s 1%
Dead zone setting: 0.1%~9.9% adjustable
Protection level: standard configuration IP67 IP68
Ambient temperatūra: -20C~+60C special 40C~+70C
Ambient mitrums: Mazāk nekā vai vienāds līdz 95% (+25 grāds )
Duty cycle: On-off type is S2-15min short-time duty cycle
modulēšana tips is S4-25% intermittent duty cycle
Sprādziendrošs zīmes: Exdl, Exdib I BT4 and Exdib II CT4
Darbība procedūras
1. The construction unit should install the gate hoist on a flat, solid foundation with good redzamība, and the body and anchor must be firm. The gate hoist and the center line of the guide pulley should be verti aligned, and the distance between the gate hoist and the pulley should general be no less than fifteen meters.
2. Before the adjustment operation, the wire rope, clutch, bremze, safety sprūdrat, transmisija skriemelis, etc. būtu jāpārbauda to nodrošināt drošība un uzticamība pirms ekspluatācija. The wire rope must armanded kārtīgi on the drum, and at vismaz trīs pagriezieni must be keeped laikā operation. Laikā operation, no one is allowed to cross the wire rope of the gate hoist to prevent accidents.
3. Kad celšana smagi priekšmeti un palikšana in in air, in papildinājums to lietošana bremze, the sprūdrats drošība karte vajadzētu jālieto. Laikā operācija, it is stingri aizliegts atstāt the post bez atļaujas.
4. Laikā darbs, signāls of komandieris vajadzētu jāpakļaujas. Kad signāls ir neskaidrs vai var cēlonis negadījums, operācija jābūt jāaptur un operācija var būt turpināt pēc situācija ir noskaidrots. Ja tur ir ir a pēkšņa jauda pārtraukums darbības laikā 2c slēdzis vajadzētu jāvelk jāvelk vaļā nekavējoties un transportēti objekti vajadzētu jābūt jābūt nolikts uz leju.
Testēšana
1. Operators of the vārti pacēlājs must master the structure, performance and operation method of the gate hoist and have certain mechanical knowledge to ensure normal operation of the machine.
2. Pirms operācija, uzvedība a visaptveroša inspekcija of vārti pacēlājs uz pārbaudīt vai ieeļļošana of katra daļa ir labs un vai skrūves ir vaļīgas.
3. Kad vārti pacēlājs is darbojas, the operators nedrīkst aiziet the site and stop the machine immediately if any problem is found.
4. Kad remonts mašīna, slodze jābūt jānoņem.
5. Kad in use, eļļošana eļļa must ininjected from the oil filling hole at any time. Sufficient lubricat oil must maintained at all times. The skrūve must be cleaned of grease and coated with new oil regular to prevention rust.

Citi produkti
Piegādātājs motors liels ātrums slīpums pārnesums daudzapgriezienu elektriskais izpildmehānisms


daļējs pagrieziens plūsma vadība tauriņš vārsts elektriskais izpildmehānisms

Populāri tagi:
